• Name: sébastien
    Date: 2010-07-29 01:19:01
    [No: 1079]
    Hello,

    Do you have a distributor in France that sells one of your smallest milling machine, the SX0 ?

    Thank you.

    Dear Sebastien,

    We do not have a distributor who sells SX0 in France until now, but you can contact with our distributor and place an order. Then , they will buy one from us for you.

    Best regards,

    Nancy

  • Name: cho
    Date: 2010-07-28 23:32:13
    [No: 1078]
    Hello
    I have the SX2, can you send me
    technical documentation about
    the "Sieg SX2 BLDC Driver"

    Regards

    cho

    Dear Cho,

    Thank you for using SIEG machine.

    I will contact with you buy email.

    Best regards,

    Nancy

  • Name: Ken Miles
    Date: 2010-07-28 17:11:26
    [No: 1077]
    Hello,
    I would like to buy a replacement drive belt for a Sieg CJD250 lathe.
    Can you tell me the cost to buy and ship to New Zealand please.
    Many Thanks
    Ken.

    Dear Ken,

    Thank you for using SIEG machine.

    Where do you buy the machine before, you can buy the belt from them too.They can offer you good after sales service.

    If there are any other problem, please contact with me, thank you.

    Best regards,

    Nancy

    nancy@siegind.com

  • Name: mr J Hobbs
    Date: 2010-07-22 19:55:15
    [No: 1076]
    Hello , could you please help I have bought a sieg C1 micro lathe . I stalled the motor and blew the fuse , I replaced the fuse and now every time i switch on the speed controller the fault light comes on and the motor will not spin . A friend of mine checked the speed controller and said it was fine , what do you think it is ?

    Dear J Hobbs,

    From your words I guess that the PC board is broken down, please change a new PC board.

    Where do you bought the C1? please take an photo about your PC board and then send it to the seller, and buy one from them, thank you.

    Best regards,

    Nancy

  • Name: Franco
    Date: 2010-07-22 05:13:16
    [No: 1075]
    Sieg,

    It´s a shame that Brazil´s distributor Celmar charges a 4x overprice over US distributors. Customs duties here are around 60%, so it should cost 1.6x US prices. I´ve been wanting to buy a lathe and mill for my hobby, but will simply refuse to be abused by Celmar. I encourage you to force them to lower their profit margins by setting suggested retail prices.

    Thanks!

    Dear Franco,

     The price is decided by our ditributors, we don't make the price for them, but I will send your advice to them, thank you.

    Best regards,

    Nancy

  • Name: Gabriel
    Date: 2010-07-17 20:33:12
    [No: 1074]
    Sra Nancy
    Necesito por favor el diagrama de partes, circuito y manual de fresadora KX3B-24E
    la comunicacion de la maquina es por puerto Eternet Lan y el software que tengo es Mach3

    Desde ya muy agradecido.

    Gabriel Piatti

    Dear Gabriel,

    Could you please send English message to me under yiping@siegind.com.

    Thanks,

    Sparkling

     

  • Name: Ulrich Glimm
    Date: 2010-07-15 13:43:39
    [No: 1073]
    How do I get repair service for my Sieg KX3 servo mill with the damaged way seal cover?
    How do I get a replacement cooling Fan for my Sieg KC6 lathe?

    Dear Ulrich Glimm,

    Thank you for using our machine.

    Our sales managrer Ms.Yang have contacted you by email about this problem.

    If you have any problems, please let me know.

    Best regards,

    Nancy

  • Name: Patricio Rodriguez
    Date: 2010-07-13 00:53:28
    [No: 1072]
    Dear Sirs, Could you tell How I can purchase a nano lathe and a nano mill and to get them shipped to Santiago-Chile

    Thanks

    Dear Patricio Rodriguez,

    Thank you  for  keen on our products.

    Our sales manager will contact with you by email,thank you.

    Best regards,

    Nancy

  • Name: Guy Emanuele
    Date: 2010-07-12 22:11:18
    [No: 1071]
    sorry, I forgot to give you the model number. It is a micro lathe model C0.
    Thank you,
    Guy

    Dear Guy,

    Thank you for your detial information, I will contact with you by email.

    Best regards,

    Nancy

  • Name: Guy Emanuele
    Date: 2010-07-12 11:37:51
    [No: 1070]
    I found a couple of broken wires on the rpm control. I need a manual and a wiring diagram. I appreciate your help.
    Thank you,
    Guy

    Dear Guy,

    please tell me when do you buy the machine , the code of the machine,

    and I will be very appricaited if you can take an photo for me. And please send them to my email: nancy@siegind.com, thank you.

    Best regards,

    Nancy





1 + 4 =

Submit Cancel